Anker’s Ultra Slim Extended Battery Case gives the best combination of good performance, price for the capacity, and physical size (the level of bulk it boosts the phone). They have the capacity to offer 117 percent of the full charge to an iPhone 6 or 108 percent for an iPhone 6s. The cost tag, $40 at this writing, is crazy low for any battery case: At this rate, the Ultra Slim provides the best charge value (a 2.9 percent charge per dollar, or $34.34 for a full charge, for that iPhone 6) of some of the cases we tested, by far.
The Ultra Slim doesn’t provide an especially premium feel. That’s not to imply it comes off as cheap, but nothing about its physical construction is particularly impressive close to other cases. Another minor strike against this Anker case is its absence of button coverage; we typically prefer (well-designed) press-through button covers that protect the iPhone’s various buttons and lower the volume of places where dust and dirt can get beneath the iphone6 case.
For that iPhone 6 Plus and 6s Plus
Anker doesn’t make an Ultra Slim for your iPhone 6 Plus or 6s Plus, so for people handsets, we love to the Tylt Energi Sliding Power Case. Unlike the majority of the models we tested, this one includes a separate protective case that you could slide out from the battery sled when you don’t require the extra power, making it a much more-practical choice for the already huge Plus models. It’s additionally a great source of energy, providing generally a 93 percent charge towards the iPhone 6s Also in our tests.
An essential thing to keep in mind using the cases we dismiss below is that they will not be necessarily bad. Although we’re noting any issues we saw by using these cases, many of them are fine-they simply can’t quite match up on the top quality of our own picks.
Our previous pick for any more protective case was Speck’s CandyShell. A perennial favorite, it has two layers of material-plastic externally, rubber on the inside-that supply more protection than case designs that happen to be just one or maybe the other. The CandyShell is 10.9 mm thick, which puts it on the chunky side, nevertheless it doesn’t feel exceptionally bulky, and it’s one of the only cases we tested which claim to fulfill military drop-test standards. Speck supplies the case in an array of colors, and variants add rubbery grips (CandyShell Grip), credit card holders (CandyShell Card), and graphic prints (CandyShell Inked).
The CandyShell carries a few conditions that keep it from becoming a top pick, though. For starters, the CandyShell’s glossy back very quickly attracts small scratches that generally aren’t visible directly but jump out whenever you see the iPhone with an angle. Granted, these scratches don’t affect the protection the case offers-and we’re obviously happier to find out scratches about the case as opposed to in the phone itself-but it might be nice if Speck were to give the case having a matte finish.
One other concern is the case’s shape. Some of our readers, and also a contingent of Amazon reviewers, take trouble with the point that the CandyShell’s back is slightly convex. Specifically, once you set the truth on the flat surface, this “hump” causes the way it is to rock once you press along any kind of its edges, or perhaps to spin similar to a top if you push it. (If you obtained a CandyShell and also you mind this spinning and rocking, Speck says to contact its customer care department.)
OnePlus (the Android phone maker) surprisingly decided to go into in the iPhone-case game featuring its Sandstone Case. The important draw is OnePlus’s Sandstone texture; TIME states that it “feels like smooth sandpaper” and this “[i]t’s super grippy, rendering it very difficult to drop.” Unfortunately the way it is is really a shell with open top and bottom edges, meaning it’s less protective than the usual good case needs to be. As a result design drawback, it fell out of competition.
SwitchEasy has a mixed history, one that means it is tough to tell the total story according to its cases alone. Its Numbers case was our original pick for that iPhone 5 and 5s, before a wave of reader complaints about quality and customer service. The answers we got from SwitchEasy weren’t thorough; mostly, the company blamed the problems on third-parties selling knockoffs of its products. (At iLounge, I stumbled upon the SwitchEasy protectors to be impressive in general-the Numbers earned a rare A rating from me-but readers there contacted me about similar issues.) Ultimately, we pulled our recommendation.
With all of that at heart, we considered three SwitchEasy cases to the iPhone 6. First is the Odyssey. Like some of the better cases we’ve evaluated, it’s a mixture of plastic and rubber. As opposed to being layered, the materials run side by side, with the hardened rubber making up most of the case. It isn’t the prettiest case, in our opinion, however it is protective. It covers the buttons without reducing a lot of their clickiness, and six holes along the important thing up precisely with all the speaker vents. Our favorite section of the case is definitely the port protection: Rubber protectors squeeze into the headphone and Lightning ports, respectively, when they’re not being used, keeping dust along with other debris out.
SwitchEasy’s Tones includes a similar port protection and uses the identical materials. The entire body is usually plastic, though, with all the rubber walking around the edges like a border and also across the rear of the truth, matching the iPhone’s antenna lines. We’d should you prefer a layer of rubber in between the handset along with the plastic back from the TPU iphone6 case manufacturing , and the Sleep/Wake button takes a bit a lot of pressure around the number of units we tested.
Our initial impressions of SwitchEasy’s Numbers were very positive-we had been prepared to name it as a our top pick-but there’s much more on the story than only our review units, and we found a significant fault after some extended use. This example is virtually identical to the Incipio NGP, however it provides more protection. Instead of leaving the phone’s ports totally exposed, the case provides protectors that suit into the headphone-jack and Lightning-port openings to keep dust and debris out. It’s a good touch that’s executed well. Even the phone’s speaker is way better protected, with six individual holes rather than one long opening. We actually much like the tactility from the devqpky94 a little bit more with SwitchEasy’s model than with Incipio’s case, too. An early yellow version from the case we tested accumulated permanent stains, but later iterations exhibited no such issue. However , the truth is a bit too loose, and so the corners come off too easily. We experienced this problem time and again while removing the encased phone from my pockets. Because we’ve had other issues with SwitchEasy cases before, we’re still a lttle bit wary. Should you do plan to purchase a SwitchEasy case, we recommend buying it directly through the company’s website. The process will eliminate any potential warranty problems with third-party sellers, if you have any problems with the situation.
An important thing to keep in mind together with the cases we dismiss below is the fact that, unlike with other kinds of products we cover, they are not necessarily bad. Although we’re noting any issues we saw using these cases, many of them are fine-they only can’t quite match to the premium quality in our picks.
Combining a rubber skin having a plastic frame, the Spigen Neo Hybrid is actually a slim, attractive case. Its fatal flaw is in its button protection. The silver plastic pill within the Sleep/Wake button doesn’t depress properly, so it might not hit the control underneath, and also you likely won’t feel it if it does. Former Sweethome editor Joel Johnson confirmed this matter with the iPhone 6 Plus version. Because we received this case for testing so early, we think Spigen might revise later editions to deal with this concern.
Also from Spigen may be the Ultra Hybrid, a single-piece case that fuses a rubber frame with a clear plastic back. It’s a nice-looking case, but once again, it offers complications with the buttons. As opposed to putting raised material over them, it provides left and right edges which can be flat all the way through with small indentations. To the Sleep/Wake button, the indented label says “PWR,” and for volume, you obtain plus and minus signs. Without a more pronounced physical distinction, you may more easily miss the buttons, as well as the frame moves inward once you press.
Twelve South is up front about just how protective the SurfacePad is. In the FAQ part of the case’s website, the business says, “SurfacePad for iPhone will not be designed to protect iPhone from falls, drops, being run over with a car or dropped from the loo. SurfacePad is meant to guard your iPhone from scratches and scrapes from things such as car keys, nail files or concrete park benches.” It’s actually a lesser case and a lot more of the leather sticker using a cover. The SurfacePad adheres to the rear of the iPhone, and you will get rid of it and reapply it as necessary (though accomplishing this is just not as elementary as the business will have you believe). We like the type of material, but the SurfacePad is tough to recommend unless your primary issue is fashion.
The Vault Slim Wallet from Silk is actually a much-less-expensive substitute for sister company CM4’s Q Card Case. It’s basically the same design, except rather than a faux-leather back, everything is constructed of TPU. Just like the Q Card Case, the Slim Wallet can hold three cards, but an elevated arch within its card slot causes the cards to curve to your noticeable degree, which may damage the cards with time. The Q Card Case’s positive attributes otherwise carry over, but due to card bending, I’m a lttle bit wary of the Slim Wallet.
Silk now offers the Armor Tough Case and PureView Clear Case. The Armor Tough Case is really a rubber case with interchangeable, polycarbonate-plastic backplates. It’s a great case at a reasonable cost, but it’s thicker than than our top pick, the NGP. The PureView Clear Case, however, is really a nice pick from the very full category of cases with rubber edges and clear backs, and Silk prices it aggressively. But we’re not terribly keen on this style as a consequence of dust’s propensity to acquire beneath the transparent back, and because of the ease with which the plastic can scratch. Still, beside others we’ve tested, the PureView Clear Case has pleasant-feeling buttons and well-sized port openings.
With Incipio’s Rival, unlike with all the NGP, simply the border is TPU; the remainder of the Rival is tough plastic, about .3 mm thicker compared to NGP. The rest in regards to the case is basically similar to around the NGP, like the cutouts for your ports and the caliber of the button protection. Whilst the Rival is quite smooth, much like the NGP, horizontal lines all over the lower two-thirds from the back put in a distinct texture. It isn’t as neutral because the NGP, but if you want the design, this is a great option.
Tech21’s Evo Mesh, which features the next generation from the company’s shock-absorbing lining, is an Apple Store exclusive. Similar to Tech21’s Classic Shell (much more on this design below), it’s a rubber case having a colored band walking around the perimeter. The dimensions are basically identical between the two. There’s something about this one which we like over the Classic Shell, but it’s challenging to put a finger on which which is. Perhaps it’s how the somewhat-obnoxious orange band has been replaced by colors matching the numerous body shades of the case itself. Overall, though, this situation is just too pricey for the purpose it offers you.
Plastic and rubber having a clear back, the ITSKINS Venum Reloaded drops the ball in terms of covering the iPhone’s buttons. Just like the setup of Spigen’s Ultra Hybrid, the design of your Venum Reloaded makes virtually no physical distinction between the button coverage and all of those other case. This case have also been relatively expensive when last we checked, along with the plastic border frame feels fragile.
Really a greater portion of a fashion case, the Nitro Forged from ITSKINS currently costs a pretty penny at nearly $70. It consists of a rubber skin with machined aluminum caps that attach at the very top and bottom. Thankfully, this design is surely an improvement over previous versions, which required you to make use of an included screwdriver to put in and remove the caps; instead, it uses small plastic clips that you could devote and remove by hand.
Also from ITSKINS is definitely the Evolution. A rubber core having a plastic frame, the Evolution has some curves which help help it become feel a little more organic. The big problem is the fact that screen rises above the fringe of the case as an alternative to the opposite. Consequently if you drop your handset, there’s much more likelihood of injury to the display than with other cases.
Incipio makes a lot of cases which we can’t expect great things out of every one. The EDGE is really a plastic slider, a style that’s relatively rare today. The smooth, matte-finish plastic splits into two pieces for both installation and docking purposes. Even though it offers proper button coverage and a nice protective lip, we found the situation to get too tight; pulling them back, specially the bottom cap, can be a struggle.
Weighing a number of grams greater than the normal of all the cases we tested, the DualPro SHINE is really a solid contender from Incipio. It incorporates both plastic and rubber layers, although as an alternative to being molded together, they’re two distinct pieces. The rubber is reasonably thick but doesn’t dampen the tactility from the buttons in any way, and it also still provides acceptable access to the ports. The port openings are identical to the NGP’s. We checked out the typical DualPro, with a matte finish. It’s quite nice, but it’s thicker compared to NGP and lacking the mil-spec rating from the CandyShell.
The plastic layer of the DualPro SHINE suits grooves from the rubber, helping the case feel as if a cohesive unit. We believe probably the most polarizing thing about this case is its texture: Designed to look like brushed aluminum, it certainly doesn’t seem like that, as well as least in our tests, the effect is really a certain amount of cognitive dissonance. It’s not necessarily a bad thing at all, but overall it merely doesn’t feel quite as nice as it looks.
If card storage is important to you, Verus’s Damda is a fine case. The entire body is constructed of black rubber, with nice button protection and properly centered openings for your headphone port and microphone, the Lightning port, along with the speaker. Coupled to the back is actually a plastic compartment that adds both mass and depth. A plastic door slides accessible to reveal space for a couple of, maybe three, bank cards. We initially found it a little hard to open, although with some cards inside it’s easier to work alongside yet still secure. This really is more of a niche case than our pick.
Verus’s Crystal Mixx supplies a transparent window as well as a rubber frame. Your back with this one is plastic, that is one of the two drawbacks. In our knowledge of iPhone cases, clear plastic scuffs easily and definately will show those scratches within a matter of days. This example is probably not so bad if the frame provided a better lip. Unfortunately, at .3 mm, it’s one of your shortest lips we saw, and yes it may lead to problems should you drop your iPhone.
The Protector Case and Voyager Case from Pelican look a good deal alike, with each model is difficult to acquire-Pelican doesn’t sell them online, and also in our experience they’ve been reliably available limited to AT&T retail stores. The Protector is actually a bulkier, more-angular undertake the CandyShell design with no additional benefits, so we’d pass upon it. The Voyager adds port protection and funnels the sound in the speakers forward. In addition, it has a belt clip and screen film. We notice this model as an alternative to an OtterBox case, as it’s basically overkill. The majority of people simply don’t need this degree of protection, especially not should they have to go out of their approach to finding it.
PureGear’s Slim Shell Case is available in seven color combinations, including clear-on-clear. This model is challenging plastic having a rubberized but still rigid frame. The metal button covers really are a great addition, helping the case feel more premium. It won’t offer just as much protection being a CandyShell, so it isn’t a high pick, but this one isn’t a bad option by any means.
One of the 1st iPhone 6 cases to be publicly sold-we saw it since May 2014-Minisuit’s Frost is undoubtedly an inexpensive TPU skin. Though it does fit, it offers almost no lip, and also the holes along the bottom are uneven to begin looking warped.
Monoprice is recognized for inexpensive products of all sorts. We like a few of the company’s accessories-it makes great cables, as an example-but Monoprice cases generally don’t impress. Materials often feel cheap, along with other companies offer higher-quality products at similarly the best prices. As an example, the Metal Alloy Protective Case (available in gold, silver, and cosmic blue) includes thin, aluminum shell that snaps across a thin TPU skin, with lines matching the iPhone’s antenna breaks. The TPU doesn’t feel as nice since the material that Incipio and other companies use, and the case exposes the Apple logo on the back of the phone.
Monoprice’s Industrial Metal Mesh Guard Case (in black or white) feels a bit nicer but is even less protective. The plastic shell has has a cool-looking steel grille over it, but it leaves the most notable and bottom edges unprotected, plus it features the most important Apple-logo opening we’ve seen on any case.
We looked at the TPU case from Insignia, a Best Buy brand, and it seems to be in the same OEM as Monoprice’s TPU case, but at the higher price.
We don’t like the Monoprice PC TPU Protector Case as much, although it does offer arguably more protection. This model splits into two pieces, with an inner skin of TPU as well as a polycarbonate shell that snaps in place over it. The case is fairly very easy to assemble, but when it’s together, it just feels big. It’s both wider and thicker than the NGP, without having obvious advantage other than price.
Rokform has long focused on ruggedized cases that will connect with an ecosystem of mounting accessories. Its Sport v3 is no exception. This plastic and rubber case includes swappable magnetic backplates that allow it to connect with various mounting brackets the organization sells. Unfortunately, the instruction insert lists a dealbreaker: “Magnet will disable NFC on phone.” Today the company claims that the magnet won’t hinder Apple Pay or any antennas, but we haven’t tested this.
OtterBox’s Defender Series may be the bulkiest from the cases we’ve tested up to now. Here is the company’s flagship case, the one most people associate with all the brand. It’s made up of a plastic frame that snaps across the handset as well as a thick rubber skin that covers everything. Unlike many other cases, this model includes flaps within the vibration control switch, headphone port, and Lightning port-all good things to have an extra amount of protection. Additionally, it includes button coverage, but we learned that it takes more force to depress the amount and power controls than other cases do.
The Defender Series is additionally really the only case we’ve tested with built in screen protection in the form of a specific film integrated into the frame. Since you get a little space in between the protector along with the screen, very light presses and swipes may well not register, which is actually a drawback. Atop the Touch ID/Home button is really a thin sheet of plastic that didn’t hinder the event in your testing. As the Defender Series does expose the Apple logo, the way it is at least covers it with clear film that prevents it from getting scratched. And as an added bonus, the Defender Series has a belt holster.
From the OtterBox family, the Commuter Series represents the next step down in overall protection. As an alternative to plastic on the inside and rubber externally, the layers are reversed. The case still offers port coverage, although the switch on the iPhone’s left side remains exposed. Thankfully, the buttons depress far more easily. As opposed to a permanent screen protector, OtterBox includes an optional film using this type of case. The Apple logo is once more exposed, now with no plastic covering it. Besides the port protection, this example offers no obvious benefits over a CandyShell, as well as the dimensions are a drawback that keeps this model from earning a top spot.
The Symmetry Series is really a relatively recent accessory for the OtterBox lineup as well as the slimmest of those all. It feels as though a direct reply to the CandyShell, featuring its dual-layer design. This example gives the same measure of protection as our top choice plus a substantial lip. It’s taller and wider, though, at the higher price. The biggest benefit is with a matte-plastic back, it won’t show the scratches a CandyShell does.
OtterBox’s newest case, the Statement Series, is undoubtedly an iPhone 6/6s-specific case. An iPhone 6/6s Plus version exists, but unlike OtterBox’s other lines, this series offers no version for older iPhones or another flagship smartphones. It’s also one of your few OtterBox cases that put aesthetics first, featuring its large back-panel window and leather-covered lower quarter being its key distinguishing features. We’re testing the Statement at this time, and we’ll decide if it should join our picks soon.
The Hard Candy Cases Candy Clip Series is a fairly crazy proposition: For $30, you get yourself a hard-plastic X-shaped piece that snaps onto the rear of the iPhone, covering its corners and several of the edges but leaving the buttons and most of the sides exposed. No thanks.
Urban Armor Gear’s Case is one of your only cases we’ve tested to satisfy military drop-test standards. It’s excellent as a protective case, but its industrial aesthetic lacks the broad appeal of simpler designs like those from Incipio and Speck. UAG also combines plastic and rubber in this instance, but instead of a glossy finish, it relies on a matte one, with an industrial appearance that appropriately matches the brand’s name. With ridges and fake screws, it looks like something which would not be out of place on the construction site. We do take issue with the 2 small, rectangular holes on the rear of the case-about a quarter of how from the top or bottom, respectively, they expose part of the logo as well as the top 50 % of “Phone” from the iPhone label. It’s an unusual design decision with an otherwise impressive case. On the flip side, this model does come with a screen film, whereas most iPhone cases don’t nowadays.
Tech21’s entire product lineup will depend on D3O, a licensed material the organization uses in just about every one of their cases. Mostly present in the borders of Tech21 cases, the bright-orange material is supposed to remain soft when at rest but automatically harden upon impact, dissipating the force and ultimately preventing harm to your phone. The organization really likes to exhibit the stuff; every one of its cases is in least translucent, or else transparent, across the edges.
From Tech21, we tested the Classic Shell, Classic Shell Cover, and Classic Shell Flip. The initial one is the most basic, a glossy TPU skin that’s wider compared to the NGP, thanks to the layer of D3O. We’d want to see a bigger lip than this case offers, and also the buttons certainly are a bit squishier than we generally prefer. The Classic Shell Cover keeps the identical frame but replaces the TPU around the back with a hard-plastic plate, and has an attached cover to protect the iPhone’s display. Anything else works exactly like together with the standard model, as well as the lid has a cutout across the earpiece to help you speak on the phone by using it closed. The Classic Shell Flip is largely exactly the same, only as an alternative to plastic this situation carries a leather feel (it looks to be the fake stuff), as well as the lid comes around from your bottom rather than side. We find that lids get in terms of how more than they guide, so neither of the covered models excites us, and the soft buttons and wider body from the Classic Shell prevent it from obtaining a recommendation.
From iLuv, we received two cases for evaluation: the Aurora Wave and Gelato. The initial one is a basic silicone skin having a grid on the back that glows at nighttime. With regards to body coverage, the situation lives around what we’re looking for, but making this type of design involves a minimal standard of difficulty. As we’ve often found with cases with this style in past times, the vertical edges can pull out of the body of the phone more readily when compared with other cases, allowing dust and other particulates to acquire underneath. The Gelato, on the flip side, is iphone7 case having an attractive checkerboard pattern around the back. It appears and feels pretty decent, but the .33-millimeter lip is simply too short.
Poetic’s Atmosphere can be a thin case made of dual-molded polycarbonate plastic and TPU. The softer material rings the leading edge to create a small lip, and in addition it runs across the antenna breaks on the rear of the phone. Even if this transparent case initially looks like a fantastic option for individuals that want a slim protector yet still want to demonstrate their iPhone, it falls short as a result of button protectors that need excessive force to press.
Macally shipped us a handful of different cases, but two seem to be styles we simply can’t recommend. Both the Metallic Snap-On Case and the Flexible Protective Frame come in a variety of colors, however the former is a shell, along with the latter can be a bumper that protects the sides but leaves the scratchable back exposed. The Durable Protective Case, on the other hand, does offer more thorough protection, unfortunately it isn’t a unique design. A combination TPU skin and hard-plastic frame, this situation form of looks like an armadillo through the back. We’ve already seen at least one other company offering the same case, and that we weren’t impressed with that case’s aggressive looks either.
New Trent’s Alixo 6S isn’t necessarily the prettiest case around, yet it is one from the more original designs we’ve noticed in the pile. This two-piece case consists of a front frame (black- and white-rimmed versions are included in the package) along with a silicone rubber and plastic back. You merely snap the phone into your selection of frame after which insert it in the back piece, which include flip-open port protectors. The level of protection this model offers for the pricing is impressive, because it includes a built in screen film and Touch ID coverage. But the latter ends up being the Alixo 6S’s downside: Even though the fingerprint sensor does deal with the thin material over it, we found that it is less reliable, requiring more efforts to unlock the unit.
Marblue’s ToughTek is really a thick silicone rubber case that accompanies a screen protector. While we don’t doubt this thing are able to tolerate some significant drops, the ToughTek is large-3 inches wide, 5.8 inches tall, and .6 inch deep-and particularly difficult to get in and out from tight pockets due to the grippy material. It may not be described as a bad option if you’re handing your iPhone 6 to kids.
The Elite, also from Marblue, takes its inspiration from the CandyShell, while incorporating an Aztec-like pattern. The plastic and rubber layers intersect in horizontal and vertical lines, using the latter material sticking up higher than the hard plastic. Probably the most intriguing part of this case is definitely the pair of inch-long ridges, one on either side. They’re made to work alongside an array of accessories, together with a belt clip. We’ll be keeping an eye out for these particular accessories, and we’ll decide if they boost the price of the situation.
We had high hopes for your Spigen Capella, which can be found in multiple colors. Its setup is nearly the same as the CandyShell’s, with rubber inside and plastic outside. The big difference, and the reason we were interested in it, is it’s much slimmer, measuring about 2 mm thinner from front to back. This is partly as a result of smaller, half-millimeter lip throughout the screen. One of the editors loves the way the case’s slight curve feels, comparing it on the iPhone 3G. Judging by the feedback we’ve seen from readers and Amazon reviewers, many people don’t that way shape just as much as we all do.
Although the Capella isn’t as deep as being the CandyShell, it really is a bit taller, and approximately 3 mm wider. This width ends up being problematic for just two reasons, one on either edge. About the iPhone’s left side, the switch is much harder to toggle, as it’s deeply recessed within the rubber border; should you don’t have nails to communicate of, moving it to and fro will probably be tough. On the other side, the Sleep/Wake button demands a surprising level of pressure to activate. If you’re willing to cope with those drawbacks, the Capella is otherwise worth taking into consideration like a CandyShell alternative.
Using its Revolution case, Poetic looks to contend with companies such as OtterBox with a far lower price. The case starts off with a plastic frame that snaps on the front in the iPhone; a definite sheet of plastic protects the screen while leaving the sensors at the top along with the Touch ID button in the bottom exposed. A rubber and plastic body fits throughout the back, snapping into position together with the front piece. Everything feels quite sturdy, the buttons click well, as well as the flap across the Lightning port can be a nice amount of extra protection.
Supcase’s Unicorn Beetle Pro Holster supplies a similar proposition. The most significant distinction between this model and the Revolution is that it includes a plastic belt holster. Having roughly exactly the same dimensions as being the Poetic case, this model requires an installation that’s basically the identical. This example adds several flaps for coverage, namely across the side switch as well as the headphone port as well as the Lightning port. While it’s an incredibly solid-feeling case, we immediately referred to as the company’s claim of dust-proof construction into question, mainly because it leaves openings for dust to go into, like the fully exposed speaker. At the moment, Amazon users are usually keen on it, with 127 reviews plus a 4.1-star (out from five) rating, but we’ve seen quite a few three- and four-star reviews.
Relative newcomer Supcase has several iPhone 6 cases, in fact, most of which are section of the “Unicorn Beetle” family. The Slim Armored Protective Case is like Urban Armor Gear’s case for the reason that it’s protective, nevertheless the design is rather specific, meaning it likely won’t attract the same wide swath of individuals as something a bit more generic. The plastic and rubber case feels sturdy and contains some of the clickiest buttons associated with a we tested. As for the lip, it’s approximately .5 mm, so it’s smaller than we’d like, and also the case makes no mil-spec claims. If you love the look, it’s not a bad choice otherwise.
Supcase also sells the Hybrid Clear Bumper Case, which combines a specific-plastic backplate using a TPU bumper. That polycarbonate back won’t absorb just as much shock since the thick rubber border, but it’s a good way to flaunt Apple’s design.
Within a previous version of the guide, we named Logitech’s Protection [ ] as a much more-protective pick. It possesses a very similar design, with the advantages of a matte finish and embedded magnets that give it time to get connected to mounting accessories. Unfortunately Logitech has confirmed that it’s no more selling the way it is, that is currently on clearance at Best Buy.
Hardly any other case we tested is set up much the same way as Maxboost’s DuraShield Series (now named DuraSLIM). Like all kinds of other models, it uses both rubber and plastic components, but here the rubber is a bumper that wraps around the iPhone’s border, along with the plastic snaps in place over it while covering the back of the handset. Inspite of the unusual design-or maybe for doing it-the situation offers superior protection in comparison with many others we’ve seen. It offers a 1-mm lip, plus speaker and Lightning-port protection. It also redirects the audio ports forward, meaning the sound comes to you, as opposed to down; the design has no impact on audio quality, thankfully. As for the Lightning port, it stays protected underneath a rubber tab that you can flip out when you want access.
Few case manufacturers actively warn that the product doesn’t offer drop protection, but such a message appears in the Amazon listing for Maxboost’s Liquid Skin. Extremely thin, this transparent-TPU case adds very little bulk towards the handset, not really a protective lip. It’s a lot better than a shell mainly because it offers button protection and cutouts for your ports, even if they are quite tight. Though with this kind of warning from your case maker itself, we can’t recommend the Liquid Skin for many people. If you’re going to employ a case, you should utilize something that’ll stand up to a drop.
Maxboost’s Crystal Cushion and i-Blason’s Halo Series are almost identical to each other and might be small tweaks on a single reference design. Both have rubber frames-the Halo Series offers six colors, plus clear-with transparent plastic backplates. The Maxboost case’s edges tend to be more squared-off, as the i-Blason’s are rounder. Both offer good body coverage and responsive buttons, although the lip across the screen is nearly nonexistent, especially on the Halo Series. Combine that with the tendency for clear plastic cases to scratch as well as to expose trapped dust underneath, and those cases aren’t top picks.
The Maxboost HyperPro Series is perfect for all intents and purposes a thicker version in the Incipio NGP. Available only in black, it uses two layers of TPU to protect the iPhone, and it also measures 10.2 mm thick; it’s also wider and taller than our pick. The buttons press well and yes it incorporates a protective lip, but we could find no real benefit to this example over the NGP, aside from savings of just a few dollars.
One of only a few slider-style cases available, Maxboost’s Vibrance Series supplies a different build than a lot of the cases we tested. A tough-plastic case, it splits into two pieces, both lined with a soft fabric across the back that’s created to prevent damage during installation and removal. As opposed to pushing the phone to the case, you pull off the base cap, slide the phone to the top, after which push the pieces back together. Much similar to the STM Harbour, this kind of design allows you to keep your iPhone thoroughly protected more often than not, as well as plug it into docks when necessary. The lip is almost short, though, and pulling from the Vibrance’s bottom cap is harder than flipping up the Harbour’s bottom. Maxboost even offers only one color choice, salmon by using a gold cap, which may not entice as numerous people as more basic colors would.
If you discover the CandyShell to be too large, you won’t be impressed with Speck’s MightyShell, which is available in black, orange, purple, pink, and clear variants. This model has a few key differences. First is definitely the extra layer of TPU material that can help absorb shocks into a greater degree; it adds 2 mm in both width and height, along with .5 mm for the thickness in the case. Speck claims this new design will “double MIL-STD-810G drop test standards,” but we can’t tell whether it means the case is tested to thrive drops from twice as high or it indicates the way it is can tolerate the regular 4-foot drops twice as often. One part of the case we actually appreciate is the hard-plastic exterior, that is matte instead of glossy, so it won’t show scratches nearly as readily since the standard CandyShell. For your price, we expect more than simply claims of better drop protection; the conditions where this situation would survive but a CandyShell wouldn’t are too ambiguous to warrant the charge.
Among ultrathin cases, Shumuri’s SLIM looks and feels much like Caudabe’s The Veil XT, right down to the possible lack of the typical Veil’s screen-protection lip. But it’s also missing both Veil models’ camera-lens protector. The same goes for Monoprice’s Ultra-thin Shatter-proof Case (in clear frost, ice blue, and smoke) and Totallee’s The Scarf (for iPhone 6 and iPhone 6 Plus).
Rearth USA’s Ringke Slim (for iPhone 6 and iPhone 6 Plus) offers both a screen-protecting lip and bottom-edge coverage, along with thicker plastic for added protection. However, we’re not fans of its aesthetics-for the reason that case’s rigid plastic is thicker, the business has added a small slit to every corner to make putting the way it is on your own phone easier. The design is successful enough; we simply don’t like the way it looks.
Power Support’s Air Jacket and SwitchEasy’s Nude (for iPhone 6 and iPhone 6 Plus) are glossy-plastic cases which are slightly thicker than Caudabe’s The Veil. The previous provides good coverage across the phone’s bottom edge but only has the very faintest of your screen-protection lip. The second has neither.
Amzer’s Crusta might not exactly appear to be an excellent value at $35 (iPhone 6) or $45 (iPhone 6 Plus) as of this writing, although the package includes not only a basic case. The situation itself relies on a two-piece snap-together design having a rubber bumper plus a glass back that lets the iPhone’s rear show through. The glass likely won’t show scratches as easily as similar cases we’ve seen using a plastic back, however, you will still see any dust, hair, or some other particulates which get underneath the glass. Amzer contains a second piece of glass to safeguard the phone’s screen. The case ultimately ends up being bulkier than we prefer-the iPhone 6 version is 14.4 mm thick, like the phone-but it’s one from the better cases we’ve seen from Amzer, a company otherwise known for inexpensive, nondescript accessories.
NewerTech is recognized more for computer accessories than smartphone accessories, but the company does give a collection of cases called NuGuard KX (for iPhone 6 and iPhone 6 Plus). Made more for drop protection than sleekness, the NuGuard KX boasts a thick layer of gel material that absorbs and evenly distributes shocks. The case is pretty bulky, yet an opening on the rear of the way it is for your phone’s Apple logo actually subtracts through the overall level of protection. We choose the NGP.
We have now varying degrees of praise for 3 cases from Griffin Technology. The Survivor Slim (for iPhone 6 and iPhone 6 Plus) is our least favorite of them. This bulky rubber case feels much more like an accessory for a kid’s toy than a smartphone. It could be a good case if children frequently make use of your phone, but we suspect that a lot of adults will prefer something slimmer.
We like the Survivor Core (for iPhone 6 and iPhone 6 Plus) and all of Clear Identity (for iPhone 6 and iPhone 6 Plus) better. Both enable the handset’s to show via a clear back panel. The previous has rubber edges, as well as its rubber corners protrude a bit, helping cushion the iPhone against drops-however the outcome is that it’s a bit bigger than a regular case. The All Clear Identity, however, includes a transparent back with translucent-rubber edges. The trouble, as with all cases sporting a precise back, is the fact both cases show any gunk that gets beneath the plastic. For some people, that might be a suitable compromise in the case designed to let you see your phone’s own surfaces, but we generally prefer something translucent or opaque. Neither the Survivor Core nor the All Clear identity is a bad option, but neither particularly excites us.
Belkin’s Grip Case for iPhone 6 is a great substitute for our top pick, but it really doesn’t quite create the top tier. The design is much like that of the Incipio NGP, as it’s a one-piece polyurethane case. The biggest difference is across the phone’s bottom edge: Rather than having separate openings to the headphone jack, microphone, Lightning-connector port, and speaker, the case exposes the past two through one long opening. A slight indentation from the plastic covering the base of the phone permits use with accessories like Apple’s Lightning-connector adapters. This really is a nice feature we haven’t seen on other cases, although we worry the thinness of your material here, as well as near the Ring/Silent switch, may make it more prone to ripping. Wirecutter editor Michael Zhao also finds the case’s button coverage to be somewhat problematic, while he doesn’t like that they’re nearly flush using the case.
One of the cases delivered to us for consideration, we dismissed numerous models right off the bat. We cut Spigen’s Slim Armor, Slim Armor S, Tough Armor, and Tough Armor S, along with Verus’s Thor, Iron Shield, and Dandy Diary, plus PureGear’s DualTek, because of their Apple-logo-exposing holes on the back. They actually do a decent job of protecting your phone otherwise, but we could think of no reason to recommend them for many people when existing hole-free options are as good or better.
We also dismissed a variety of shell cases because, as we mention above, they supply a minimal volume of coverage for your device’s body. Among they were the Aluminum Fit, Thin Fit, and Thin Fit A from Spigen. The same thing goes for that Neo Hybrid EX, Spigen’s bumper case, which offers even less protection.